Browse
 
Tools
Rss Categories

JetDirect Card Setup 4000, 4050, 4100, 4500, 4550, 5000, 5100, 8000, 8100, 8150, 8500 & 8550 printers

Author: Fuser Printer Parts Reference Number: AA-00113 Views: 6467 Created: 06-14-2010 04:22 pm Last Updated: 06-14-2010 04:22 pm 0 Rating/ Voters


Technical Service Bulletins

 

 

HP LaserJet 4000, 4050, 4100, 4500, 4550, 5000, 5100, 8000, 8100, 8150, 8500 & 8550 printers

 

1.                Print out a configuration page before undertaking this procedure.   Retain the EIO/Network/JetDirect Configuration Page (usually the 2nd page). This page contains the settings you will need to enter to        complete this procedure. If you are unable to print a configuration page, consult with your network administrator to obtain these settings before proceeding.

2.                Turn the printer off. Install the new JetDirect card and connect the network cable.

3.                Turn the power on and wait for the printer to reach the READY or   ONLINE state.

4.                Press MENU until 'HP EIO 1' (or 2 or 3) appears.

5.                Press ITEM until 'CFG NETWORK = NO' appears.

6.                Press VALUE until 'CFG NETWORK = YES' appears.

NOTE: The CFG NETWORK = XXX (XXX being YES or NO) is a toggle, not a permanent setting. Changing it to YES allows the settings to be changed at that time. It will appear as CFG NETWORK = NO each time this menu is accessed.

7.                Press SELECT.

8.                Press ITEM until 'CFG TCP/IP = NO' appears.

9.                Press VALUE until 'CFG TCP/IP = YES' appears.

NOTE: The CFG TCP/IP = XXX (XXX being YES or NO) is a toggle, not a permanent setting. Changing it to YES allows the settings to be changed at that time. It will appear as CFG TCP/IP = NO each time this menu is accessed.

10.           Press SELECT.

11.           Press ITEM until 'BOOTP = YES*' appears.

12.           Press VALUE until 'BOOTP = NO' appears.

NOTE: When using BootP or DHCP, keep the setting BOOTP = YES *. The BootP or DHCP server will configure the TCP/IP parameters on the HP JetDirect. No other TCP/IP configuring is necessary.

13.           Press SELECT.

The following three steps apply to the HP JetDirect 610n cards only:

    1. 'DHCP=YES' appears.
    2. Press VALUE until 'DHCP = NO' appears.
    3. Press SELECT.

NOTE: When using DHCP, keep the setting DHCP = YES *. The DHCP server will configure the TCP/IP parameters on the HP Jetdirect. No other TCP/IP configuring is necessary.

14.           Press ITEM until 'IP BYTE 1 = (value*)' appears.

15.           Press VALUE, until the desired value of the first byte of       the IP        address appears. By pressing and holding VALUE, the value will   scroll rapidly (HP LaserJet 4000, 5000 and 8000 printers have a     MINUS button to decrease the value).

16.           Press SELECT to save the value.

17.           Press ITEM to continue. Repeat Steps 11-13 to configure the        remaining bytes of the IP address.

18.           Repeat Steps 11-13 to configure the subnet mask bytes ('SM BYTE        1='), syslog server IP address ('LG BYTE 1='), default gateway       ('GW BYTE 1='), and timeout ('TIMEOUT=').

19.           Press ONLINE, GO or MENU. Print a self-test page to verify the   IP     settings.

20.           If the test page does not show the correct settings, power cycle the printer and reprint the test page.